| 1 (LH) |
15021-07200 |
110-21-072-00 |
1 |
Swing Arm Weldment, 16” CLR – LH (CCW) |
| 1 (RH) |
15026-07200 |
110-26-072-00 |
1 |
Swing Arm Weldment, 16” CLR – RH (CW) |
| 2 |
15011-29500 |
110-11-295-00 |
1 |
Gib, Slide (HIT makes a 1 pc design ref.) |
| 3 |
15010-43000 |
110-10-430-00 |
4 |
Toggle Link (w/ 2 Bushings Installed) |
| 3-A |
15010-43000-BBL |
(if sold separately) |
4 |
Large Bushing Only, T-Link (ID Sizing Req’d) |
| 3-B |
15010-43000-BBS |
(if sold separately) |
4 |
Small Bushing Only, T-Link (ID Sizing Req’d) |
| 4 |
15010-50400 |
110-10-504-00 |
1 |
Pin – Upper Rear (Includes $7 & $9) |
| 5 |
15010-50401 |
110-10-504-01 |
1 |
Pin – Clevis (Includes $7 & $9) |
| 6 |
15010-50600 |
110-10-506-00 |
1 |
Pin – Rod End (Includes $8 & $9) |
| 7 |
15010-51000 |
110-10-510-00 |
1 |
Pin – Slide (Includes $7 & $9) |
| 8 |
15010-65200 |
110-10-652-00 |
1 |
Rod End – Clamp Cylinder |
| 9 (LH) |
15011-72500 |
110-11-725-00 |
1 |
Slide – Ampco Bronze, LH (used on LH only) |
| 9 (RH) |
15026-72500 |
110-26-725-00 |
1 |
Slide – Ampco Bronze, RH (used on RH only) |
| 10 |
15011-80500 |
110-11-805-00 |
1 |
Clamp Bar – Right Side |
| 11 |
15011-80501 |
110-11-805-01 |
1 |
Clamp Bar – Left Side |
| 12 |
15010-80700 |
110-10-807-00 |
2 |
Wear Strip – Slide |
| 13 |
15011-80700 |
110-11-807-00 |
2 |
Wear Strip Extension – Slide |
| 14 |
15020-15501 |
110-20-155-01 |
1 |
Slide Hold Down Block – Swing Arm |
| 15 |
15010-15502 |
110-10-155-02 |
1 |
Wear Strip – Slide Hold Down |
| 16 |
15009-41700 |
110-09-417-00 |
1 |
Key – Bend Die |
| 17 |
15009-47500 |
110-09-475-00 |
2 |
Bearing Locknut (for Tapered Drive Sprocket) |
| 18 |
15009-81600 |
110-09-816-00 |
1 |
Stud – Bend Die (No Overhead Tie Option) |
| 19 |
15020-42300 |
110-20-423-00 |
1 |
Key – Front Drive Sprocket |
| 20 |
15020-64000 |
110-20-640-00 |
1 |
Bend Die Locating Ring – Inner |
| 21 |
15020-76500 |
110-20-765-00 |
1 |
Drive Sprocket – Front (Tapered Bore Style) |
| 22 |
15020-80700 |
110-20-807-00 |
1 |
Bend Die Locating Ring – Outer |
| 23 (LH) |
15020-83101 |
110-20-831-01 |
1 |
Lower Arm Support Bracket, LH (used on LH) |
| 23 (RH) |
15025-83101 |
110-25-831-01 |
1 |
Lower Arm Support Bracket, RH (used on RH) |
| 24 |
30040-07501 |
112-40-075-01 |
1 |
Overtravel Switch Trip Plate |
| 25 |
30040-07502 |
112-40-075-02 |
1 |
Spacer – Overtravel Plate |
| 26 |
15068-54421 |
110-68-544-01 |
1 |
Safety Plate (16” CLR Toggle Link Arm) |
| 27 |
15009-15500 |
110-09-155-00 |
1 |
Slide Back-up Block – 1” (Not Shown) |
| 28 |
15009-15501 |
110-09-155-01 |
1 |
Slide Back-up Block – 2” (Not Shown) |
| 29 |
15009-15502 |
110-09-155-02 |
1 |
Slide Back-up Block – 3” (Not Shown) |
| 30 |
15009-15503 |
110-09-155-03 |
3 |
Slide Back-up Block – 4” (Not Shown) |
| $1 |
15024-24200 |
110-24-242-00 |
1 |
Hydraulic Cylinder (Less fittings) |
| $2 |
3982 / 3920 |
(Std. Purchase) |
1 Set |
Upper Spindle Cone / Cup Bearing Set |
| $3 |
3975 / 3920 |
(Std. Purchase) |
1 Set |
Lower Spindle Cone / Cup Bearing Set |
| $4 |
AN-10 |
(Std. Purchase) |
1 |
Bearing Locknut (for Lower Spindle Bearing) |
| $5 |
W-10 |
(Std. Purchase) |
1 |
Locknut Washer (for Lower Spindle Bearing) |
| $6 |
LC-150P-18 |
(Not Pines Std.) |
4 |
Plateform Mount (Not used on all designs) |
| $7 – $29 |
(Call for info) |
|
N/A |
Standard Purchase Components & Fasteners |
