| 1 (LH) |
60021-07200 |
114-21-072-00 |
1 |
Swing Arm Weldment – LH (CCW Bender) |
| 1 (RH) |
60026-07200 |
114-26-072-00 |
1 |
Swing Arm Weldment – RH (CW Bender) |
| 2 |
60010-29500 |
114-10-295-00 |
1 |
Gib, Slide – Bronze |
| 3 |
60011-29500 |
114-11-295-00 |
1 |
Gib Extension, Slide – Bronze (48” CLR) |
| 4 |
60010-30700 |
114-10-307-00 |
2 |
Slide Guard – Brass |
| 5 |
60011-30700 |
114-11-307-00 |
2 |
Slide Guard Extension – Brass (48” CLR) |
| 6-1 |
60010-43000 |
114-10-430-00 |
4 |
Toggle Link (w/ 2 Bushings Installed) |
| 6-2 |
60010-43000-BB |
(if sold separately) |
8 |
Bushing Only, Toggle Link (ID Sizing Req’d) |
| 7 (LH) |
60011-72400 |
114-11-724-00 |
1 |
Slide – Steel / Phenolic, LH (used on LH only) |
| 7 (RH) |
60026-72400 |
114-26-724-00 |
1 |
Slide – Steel / Phenolic, RH (used on RH only) |
| 7-1 |
60010-68600 |
114-10-686-00 |
1 |
Acme Back-up Screw (if sold separately) |
| 7-2 |
60011-01900 |
(if sold separately) |
1 |
Wear Plate – Slide Hold Down |
| 7-3 |
60010-72400-WK |
(if sold separately) |
1 |
Wiper Kit for Slide (Wipers, Spacers, & Screws) |
| 8 |
60010-50401 |
114-10-504-01 |
1 |
Pin – Clevis (Includes $2) |
| 9 |
60010-50402 |
114-10-504-02 |
1 |
Pin – Upper Rear (Includes $6) |
| 10 |
60010-50600 |
114-10-506-00 |
1 |
Pin – Rod End (Includes $3 & $6) |
| 11 |
60010-51000 |
114-10-510-00 |
1 |
Pin – Slide (Includes $3 & $6) |
| 12 |
60010-65200 |
114-10-652-00 |
1 |
Rod End – Clamp Cylinder |
| 13 |
60010-80501 |
114-10-805-01 |
1 |
Clamp Bar – Left Side |
| 14 |
60010-80502 |
114-10-805-02 |
1 |
Clamp Bar – Right Side |
| 15 |
60011-80501 |
114-11-805-01 |
1 |
Clamp Bar Extension – Left Side |
| 16 |
60011-80502 |
114-11-805-02 |
1 |
Clamp Bar Extension – Right Side |
| 17 |
60010-80701 |
114-10-807-01 |
6 |
Wear Strip, Slide – Short (Std. 24” CLR) |
| 18 |
60011-80700 |
114-11-807-00 |
2 |
Wear Strip, Slide – Extension (48” CLR) |
| 19 |
60010-80705 |
114-10-807-05 |
2 |
Wear Strip – Clamp Bar, Phenolic |
| 20 |
60011-80704 |
114-11-807-04 |
2 |
Wear Strip Extension – Clamp Bar, Phenolic |
| 21 |
60020-62500 |
114-20-625-00 |
1 |
Keeper Plate – Pin |
| 22 |
60009-68714 |
114-09-687-14 |
1 |
Threaded Rod Adjuster (48” CLR Slide) |
| 23 |
60009-82700 |
114-09-827-00 |
1 |
Holder – Threaded Rod Adjuster |
| 24 |
60011-01311 |
114-11-013-11 |
1 |
Slide Hold Down Block – Swing Arm |
| 25 |
60011-01500 |
114-11-015-00 |
1 |
Slide Hold Down Riser – Swing Arm |
| 26 |
60009-41700 |
114-09-417-00 |
1 |
Key – Bend Die |
| 27 |
60009-47500 |
114-09-475-00 |
1 |
Nut – Bend Die Stud |
| 28 |
60009-81600 |
114-09-816-00 |
1 |
Stud – Bend Die (No Overhead Tie Option) |
| 29 |
60009-94000 |
114-09-940-00 |
1 |
Lower Bearing Spacer – Swing Arm |
| 30 |
60020-23600 |
114-20-236-00 |
1 |
Upper Bearing Cover – Swing Arm |
| 31 |
60020-42300 |
114-20-423-00 |
1 |
Key – Front Drive Sprocket |
| 32 |
60020-64000 |
114-20-640-00 |
1 |
Locating Ring – Bend Die |
| 33 |
60020-76500 |
114-20-765-00 |
1 |
Drive Sprocket – Front (Tapered Bore Style) |
| 34 (LH) |
60020-83100 |
114-20-831-00 |
1 |
Lower Arm Support Bracket – LH (used on LH) |
| 34 (RH) |
60025-83100 |
114-25-831-00 |
1 |
Lower Arm Support Bracket – RH (used on RH) |
| 35 |
60020-15511 |
114-20-155-11 |
2 |
Adjustment Block Kit – Lower Support (Welds) |
| 36 |
60020-94100 |
114-20-941-00 |
1 |
Spacer – Upper Bearing |
| 37 |
60040-07501 |
114-40-075-01 |
1 |
Overtravel Switch Trip Plate |
| 38 |
60040-07502 |
114-40-075-02 |
1 |
Spacer – Overtravel Plate |
| 39 |
60068-54404 |
114-68-544-04 |
1 |
Safety Plate (Not for all models, call for info) |
| 40 |
60009-15500 |
114-09-155-00 |
1 |
Slide Back-up Block – 2” (Not Shown) |
| 41 |
60009-15501 |
114-09-155-01 |
1 |
Slide Back-up Block – 3” (Not Shown) |
| 42 |
60009-15502 |
114-09-155-02 |
1 |
Slide Back-up Block – 4” (Not Shown) |
| 43 |
60009-15503 |
114-09-155-03 |
1 |
Slide Back-up Block – 5” (Not Shown) |
| 44 |
60009-15504 |
114-09-155-04 |
1 |
Slide Back-up Block – 6” (Not Shown) |
| 45 |
60009-15505 |
114-09-155-05 |
4 |
Slide Back-up Block – 7” (Not Shown) |
| $1 |
60024-24200 |
114-24-242-00 |
1 |
Hydraulic Cylinder (Less fittings) |
| $2 |
82587 / 82950 |
(Std. Purchase) |
1 Set |
Upper Spindle Cone / Cup Bearing Set |
| $3 |
795 / 792 |
(Std. Purchase) |
1 Set |
Lower Spindle Cone / Cup Bearing Set |
| $4 |
AN-26 |
(Std. Purchase) |
2 |
Bearing Locknut (for Tapered Drive Sprocket) |
| $5 |
AN-24 |
(Std. Purchase) |
1 |
Bearing Locknut (for Lower Spindle Bearing) |
| $6 |
W-24 |
(Std. Purchase) |
1 |
Locknut Washer (for Lower Spindle Bearing) |
| $7 |
LC-150P-18 |
(Not Pines Std.) |
4 |
Plateform Mount (Not used on all designs) |
| $8 – $36 |
(Call for info) |
|
N/A |
Standard Purchase Components & Fasteners |
